MFlenses - Una nueva vida en la era digital
MFLenses 2026

Foro de objetivos de enfoque manual

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.
Destacado

Espacio de socio destacado en la portada del foro.

"Errors" in film emulsion?
Ver tema anterior :: Ver tema siguiente  


Reply

Hi
I'm getting sometimes such "errors" on B/W films. It occurs maybe once in 1 of maybe 5 rolls.
They ruined a few nice shots over the time

That's TriX 400 pushed to ISO 3200 in Xtol 1+1 - but I've already seen it with other dev.-/film combinations.
Can anyone say how to avoid them?


Reply

just first idea, do you keep temperature of all liquids about the same? I´ve seen some emulsion errors when washing temperature was too hot or too cool, but never this size


Reply

I had that happen when a piece of emulsion had torn in the film spiral's clip. The emulsion came off during developing and adhered to another part of the film. So, my question is whether that part of the emulsion (while in a plastic sheet) has a different relief?


Reply

I never had similar experience.


Reply

I can't say I've experienced anything like this before either. It does look as if a big piece of something adhered to the film. Xtol, I have noticed, has a tendency to separate and get little white flakes that settle to the bottom of the container. I wonder if one of these flakes stuck to the film somehow?

The image is not entirely lost. After about 2 minutes of cloning I ended up with this:

Obviously it's still very visible but if you spend some actual time, most things are salvageable.


Reply

Attila escribió:
I never had similar experience.


Me neither.


Reply

Well I've had that problem a few times with colour negs done by the supermarket, but a much smaller irregular white patch and always assumed it was something floating around the developer\fixer that stuck to the neg. It has never bothered me as I just remove it with photoshop.


Reply

had that once when two windings of the film touched on the development reel.


Reply

Cita:
had that once when two windings of the film touched on the development reel.


Wouldn't that stop the developer from reaching the film, resulting in a dark spot?


Reply

themoleman342 escribió:
Cita:
had that once when two windings of the film touched on the development reel.


Wouldn't that stop the developer from reaching the film, resulting in a dark spot?


Yes, that is what happens. The emulsion remains on the neg and is opaque so comes out as a black area when scanned.


Reply

berraneck escribió:
just first idea, do you keep temperature of all liquids about the same? I´ve seen some emulsion errors when washing temperature was too hot or too cool, but never this size

This might be the problem
I doing the final wash a bit warmer for faster drying.
Thx!


Reply

iangreenhalgh1 escribió:
themoleman342 escribió:
Cita:
had that once when two windings of the film touched on the development reel.


Wouldn't that stop the developer from reaching the film, resulting in a dark spot?


Yes, that is what happens. The emulsion remains on the neg and is opaque so comes out as a black area when scanned.


um...
It forms a dark spot on the negative, what equals to a white spot on the positive.


Reply

Cita:
It forms a dark spot on the negative, what equals to a white spot on the positive.


I don't understand how that occurs than. Why would the film touching result in over-development in that spot? It should be the complete opposite.


Reply

themoleman342 escribió:
Cita:
It forms a dark spot on the negative, what equals to a white spot on the positive.


I don't understand how that occurs than. Why would the film touching result in over-development in that spot? It should be the complete opposite.


I'ts not overdevelopment at all Smile

If two windings touch nothing reaches the emulsion, including the fixer, so the actual emulsion stays on the film (the spot looks like undeveloped film). I've never seen it the other way around (touching while in developer and not touching while in fixer).

According to my experience this usually happens when a reel jams, and you use to much force to fix it.


Reply

Oh, I understand! Thanks for the clarification.


Reply

This, to me, looks like you are either rolling your film on the reel wrong and it is touching in those spots causing the stop, fix, whatever to stick and burn in like that... or your not washing well enough and the same is happening... also are you using powder developer? if so make sure there are no lumps in it... lumps could cause this.


Reply

In fact it kinda looks like there was absolutely NO emulsion there doesn't it... like it somehow was scratched away.