MFlenses - Una nueva vida en la era digital
MFLenses 2026

Foro de objetivos de enfoque manual

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.
Destacado

Espacio de socio destacado en la portada del foro.

How could I calibrate my lightmeter?
Ver tema anterior :: Ver tema siguiente  


Reply

I've been trusting my Sixon Gossen lightmeter for some time. I must admit that some of the pictures I took based on its performace were short of light. But since I'm always trying faulty cameras, I was doubting more on the cameras than on the lightmeter itself.

Past week I initiated a training exercise, to learn myself to estimate properly the light levels without the need of the lightmeter, and based on the sunny16 rule.
To do so, I printed the EV table (to help memorizing it) and the Exposure Factor Relationship Chart from http://www.fredparker.com/ultexp1.htm . I carry them on my backsack and at any time I see an interesting visual composition I try to estimate the light metering according the tables. Afterwards I take out the light meter and I check the reading against my estimation.
Well, I get a consistent underexposure of two steps in most cases... So my question is: Who is lying?. The chart or the lightmeter?.
So I would like to test my lightmeter, because I'm afraid it's the culprit.
Do any of you know how to do it?.

Is there any basic reference like boiling water for temperature?.
Open to any suggestion.

Thanks in advance.
Jes.


Reply

Hello,

Since all the lightmeters are calibrated using as reference the amount of light reflected by a 18% gray target, i would buy/borrow such a target (easily found in photographic stores) and then use the sunny16 rule to check the lightmeter ...

Hope this helps

Best regards


Reply

indianadinos escribió:
Hello,

Since all the lightmeters are calibrated using as reference the amount of light reflected by a 18% gray target, i would buy/borrow such a target (easily found in photographic stores) and then use the sunny16 rule to check the lightmeter ...

Hope this helps

Best regards


Thanks for the idea, but it's almost what I'm doing now (without the gray card)... I want to test both, my lightmeter and the F16 sunshine rule...

Probably what I should do is a comparative test against a a calibrated light meter... I've requested a friend of mine to lend me his...
By pointing to the same light source they should give the same measuring. But I'd like to have a fixed and repeatable reference, like "buy a Philips XXX lamp, at two meter distance, through a window of 4x4" it should give a reading of...."
or something like that.
How do the labs or manufacturers calibrate the lightmeters?.

Thanks!

Jes.


Reply

Let's change the question:

Does anybody own an "Oriel Spectral Irradiance Standard"?

"Using an Oriel Spectral Irradiance Standard that produces a NIST traceable light spectrum we now have the capability to calibrate your light meter. This direct calibration has far less uncertainty than the comparison to another light meter method and gives you the confidence you are looking for in your measurements."

From http://www.esscolab.com/whats-new/

Jes.


Reply

Jes, if we are together building a shutter speed tester, with a regular light source and a light sensor, somewhere in my mind is telling me we ought to be able to use the output of this same equipment to generate a measurable and consistent EV value, and so be able to use it for calibrating a light meter. Am I being silly?


Reply

Hi Jes,
you have already 2 high tech lightmeters , the 350D & K10D
take a shot of a gray card and tune exposure to have the peak in the center of histogram, then compare with you Gossen lightmeter

p.s: I made some test with 200iso negative and found that I can underexpose or overexpose by 2 stops without noticeable degradation
At 4 stops underexposure (3200iso), the sharpness is good but the grain is intrusive


Reply

peterqd escribió:
Jes, if we are together building a shutter speed tester, with a regular light source and a light sensor, somewhere in my mind is telling me we ought to be able to use the output of this same equipment to generate a measurable and consistent EV value, and so be able to use it for calibrating a light meter. Am I being silly?


No, Peter, what you say makes a lot of sense. Only that we use the phototransistor in "switching" mode, but if properly polarized can give a variable voltage output depending on the received light...

I've to think about this. Wink

Jes.


Reply

poilu escribió:
Hi Jes,
you have already 2 high tech lightmeters , the 350D & K10D
take a shot of a gray card and tune exposure to have the peak in the center of histogram, then compare with you Gossen lightmeter

p.s: I made some test with 200iso negative and found that I can underexpose or overexpose by 2 stops without noticeable degradation
At 4 stops underexposure (3200iso), the sharpness is good but the grain is intrusive


You're rigth, Poilu. I should get one of those graycards...

Thanks!.

Jes.


Reply

Be careful with it if you want to keep the "collector's value". The band is often very fragile and impossible to repair. This one was already broken when I got it.



Reply

Ignore the last, I mixed sixon and sixtomat, the label has worn off.


Reply

kansalliskala escribió:
Ignore the last, I mixed sixon and sixtomat, the label has worn off.


Don't worry, I like to see the internals of these beasts... Wink

Jes.


Reply

Hello,

Jesito escribió:
Let's change the question:

Does anybody own an "Oriel Spectral Irradiance Standard"?

"Using an Oriel Spectral Irradiance Standard that produces a NIST traceable light spectrum we now have the capability to calibrate your light meter. This direct calibration has far less uncertainty than the comparison to another light meter method and gives you the confidence you are looking for in your measurements."

From http://www.esscolab.com/whats-new/

Jes.


I have seen one of these when i was working at Astrium facilities in Toulouse. I think the count of zeros you have to put on a bank cheque to get one of these systems (the bulb alone will not be really useful) would suffice to pay some brand new cameras and a new lightmeter ... I think the grey card measurements in a sunny day is a bit cheaper ...

Best regards


Reply

indianadinos escribió:
I have seen one of these when i was working at Astrium facilities in Toulouse. I think the count of zeros you have to put on a bank cheque to get one of these systems (the bulb alone will not be really useful) would suffice to pay some brand new cameras and a new lightmeter ... I think the grey card measurements in a sunny day is a bit cheaper ...

Best regards


Hi Indianadinos,

I was suspecting something like you tell, so I just was jocking Smile

But many thanks for your comment!.

Jes.