MFlenses - Una nueva vida en la era digital
MFLenses 2026

Foro de objetivos de enfoque manual

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.
Destacado

Espacio de socio destacado en la portada del foro.

Pretty piesker with a problem. Help!
Ver tema anterior :: Ver tema siguiente  


Reply

So I got this gorgeous baby brother to the 250mm I profiled in another post. It is in near perfect cosmetic condition as well. The glass is also very, very good. Just some very minor coating damage on the back edge of the front element. Functionally the focus is butter smooth. The aperture though? It has a blade out of place. This is partly my fault, as when it came in I was doing a once over of function and feeling a bit of resistance in the ring I used a bit more force and the blade, probably stuck to neighbor bent out of shape and popped loose. "No biggie" I think, I have redone aperture blades on other lenses. I'll just pull it apart and get them replaced in their proper position. Front element unscrews in a housing like an old in shutter, easy-peasy. But I can't figure out how to get the aperture housing loose from the outer lens barrel. There is no lens tool lugs and barely any room at the front end to grip. I'm assuming the black inner tube with the aperture unscrew from the outer chromed barrel housing. Anybody?







Reply

Every time I've worked on manual apertures, the first move is to remove the outer silver ring that operates the aperture, it is usually held by a collar retained by grubscrews, but various other arrangements can be encountered. Then under that is normally another screw to remove which transfers the operating motion to an inner ring. This inner ring is usually held on by a retaining clip or threaded ring, which normally has places for a lens spanner. Although you have described not seeing any, so I don't know too much about this particular lens. The inner ring usually has the grooves to directly operate the blades, with the other pin in each blade located to another ring below the blades.

Be careful when disassembling, if the blade is damaged such that the pin has separated from the blade, it may drop out somewhere unseen, and you'd need to fabricate something else to do the job and epoxy it back to the blade, a tricky job.

Edit, in your first picture it does appear the retaining ring for the upper inner aperture ring does have a place for a lens spanner, it can be seen at the 11 o'clock position. Down at the 5 o'clock position it looks like the small screw to transfer motion from the outer to inner rings is located. Of course this is a guess from a photo, and could be mistaken.


Reply

Thanks! Unfortunately the notch is on one side and the corresponding spot on the other side is smooth at the rim and just inside that appears to be the top part of a threaded screw from the outside of the black ring. There are grub screws around the aperture ring which merely dissociated it from the inner ring. There are grub screws around the focus ring but when removed it will spin but not slide. There are also 2 screws mounted one above the other along the axis of the lens. Loosening them did not seem to help, though it is hard to say for sure as the only thing I could think of to turn is the black rim that peaks past the chrome barrel and it is very narrow and difficult to get purchase. I was reluctant to completely remove them.


Reply


This ring holds it i think. You will also have to remove the screw connecting with aperture ring from outside.


Reply

That lug seems at a glance like just the thing. However it has no partner on the opposite side of the aperture. What appears ro be the threads of a screw just inside the rim at the exists in that spot. I will keep trying though.


Reply

Darn hard to see on the photos, but it could also be a blackened spring-steel ring retainer, that locates into an internal v-groove and clamps the aperture assembly in place. If so, that might explain why the slot is only on one side. Those internal spring-ring retainers can be a bugger to remove.


Reply



Reply

I see the split-ring retainer! Smile Second photo, lower right see the split? That's holding in the diaphragm parts. Use toothpick-like tool like a small screwdriver to pry up and out one end of the ring and spiral it out.


Reply

That could be it. I will give it a try.