MFlenses - Una nueva vida en la era digital
MFLenses 2026

Foro de objetivos de enfoque manual

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.
Destacado

Espacio de socio destacado en la portada del foro.

Anyone got any M1.8 thread (0.35mm pitch) csk bolts?
Ver tema anterior :: Ver tema siguiente  


Reply

For some reason these just aren't around - everyone lists M1.6 and M2. Don't have to be JIS. Approx 7-10mm lengths . Please msg me...


Reply

DIY? Burkit M1.8 X 0.35 Tap and Die Set, M1.8 x 0.35 Machine Thread Tap and Round Die Right Hand https://www.amazon.com/Burkit-Machine-Thread-Round-Right/dp/B09ZTT736L

Editado por última vez por visualopsins el Dom Ago 17, 2025 8:26 pm; editado 1 vez en total


Reply

Thx for response visualopsins
Nobody seems to be able to supply M1.8's. I have a lens with missng bolt, and a diy'ed adapter* that I mistakenly tapped M1.8 only to realise that my 8mm bolts are M1.6. they fit but they're loose. My engineering friend suggested a bit of fine filler to fill out the hole, I may try that.
I've ordered a very cheap die from china....I'll try filing down M2.5's to 1.8mmm and threading them.

*My pentacon 500mm is now an adaptall Smile


Editado por última vez por marcusBMG el Lun Ago 25, 2025 11:57 am; editado 1 vez en total


Reply

Like 1 Like 1 Awesome! That looks really cool...


Reply

visualopsins escribió:
DIY? Burkit M1.8 X 0.35 Tap and Die Set, M1.8 x 0.35 Machine Thread Tap and Round Die Right Hand


diy 1,8 mm screws Shocked

Thank You Dog


Reply

kansalliskala escribió:
visualopsins escribió:
DIY? Burkit M1.8 X 0.35 Tap and Die Set, M1.8 x 0.35 Machine Thread Tap and Round Die Right Hand


diy 1,8 mm screws Shocked

Thank You Dog


Fixed. Thanks!

https://www.amazon.com/Burkit-Machine-Thread-Round-Right/dp/B09ZTT736L


Reply

Thanks visualopsins. That's the body of a tokina 2x tc, cut down and fitted with the ad mount off a fungussed 80-210mm. It was a bit finicky because the pentacon has a prominent raised ridge on its mount, I had to shape an acrylic disk to fit over that.

And the substitute mounts for takumar 500mm and 1000mm are done too.
I made 4 of these so three available to interested persons, who would like the facility of adaptall-ising their 500mm f4.5 or 1000mm f8, easy adaption to any camera, use the tamron adaptall 02F eyepiece adapter and have a nice big scope.
Pic 2 shows the sub mount next to the mount off my K 1000mm. AFAIK the mounts are essentially the same, taks and K series, K series are K bayonet of course



.


Reply

If you are able to apply sufficient torque for the application Loctite 222MS (purple) for small (under 1/4"/6MM) fasteners will adequately fill gaps up to .2MM when used correctly.


Reply

My small dies arrived from China - M1.8 and a M1.7. I filed down a M2.5 12mm bolt using my drill press and a small "warding" flat file and rethreaded it M1.8 - success. But the fit of the bolt was just too tight - M1.7 after all not M1.8, fortunately I had had the wit to get that die too. So I successfully took the M1.8 down to M1.7 (same pitch) and replaced the missing bolt. Then I tried to take down a second one and ....disaster. The bolt snapped leaving a stub jammed in the die. Didn't have the wit to get two of each of them while I was at it, should have done they were that cheap.
Any ideas to get out the snapped off stub?

The dies are just 11.9mm across (15/32"), I made a holder out of a small piece of 6mm polycarbonate sheet. Rather than attemp to turn the die on the bolt shank, I used a screwdriver to screw the bolt into the die.

I decided to rethread the screw holes on the adapter I made for the pentacon 500mm for M2 bolts, that worked fine.


Reply

Heat the die? Somehow screw out broken stub from other side, perhaps with another screw?