| Ver tema anterior :: Ver tema siguiente |
| Autor |
Mensaje |
Srdjan
 Registrado: 11 Abr 2012 Mensajes: 316 Ubicación: Nis
|
 Publicado: Mar Mar 18, 2014 8:11 am Asunto: !!!rollei qbm Distagon 35mm F2.8 disassembly!!! |
|
 Publicado: Mar Mar 18, 2014 8:11 am Asunto: !!!rollei qbm Distagon 35mm F2.8 disassembly!!! |
|
|
Srdjan wrote:
I need HELP for rollei qbm Distagon 35mm F2.8 disassembly. Until now I open over a 20 lens of QBM mount and all of them are the same like in this tutorial http://forum.mflenses.com/carl-zeiss-planar-or-voigtlander-color-ultron-50-1-8-repair-t49749.html. But now I tried to fix Distagon 35mm F2.8 QBM and I figure it out that this lens is quite different inside. Even I opened Voigtlander Color-Skoparex 35mm F2.8 and it is same like the rest QBM lenses. But Distagon 35mm F2.8 is different. When I start to disassembly I figure it out that I cant reach 3 screws inside beck block that separate mount from aparature ring and rest of beck elements. Plastic ring that is also A/M switch block any further attempts of disassembly beck part and fixing this lens. Anyone any idea hoe to disassembly this part. I need to fix it because aparature ball is felt out and everything is stuck. _________________ Perfection is just another type of anomaly |
|
| Volver arriba |
|
 |
calvin83
 Registrado: 12 Abr 2009 Mensajes: 7740 Ubicación: Hong Kong
|
 Publicado: Mar Mar 18, 2014 10:14 am Asunto: |
|
 Publicado: Mar Mar 18, 2014 10:14 am Asunto: |
|
|
calvin83 wrote:
This one?
http://www.bigeye.url.tw/big5/d_cz35_28.htm _________________ The best lens is the one you have with you.
https://lensfever.com/
https://www.instagram.com/_lens_fever/ |
|
| Volver arriba |
|
 |
Srdjan
 Registrado: 11 Abr 2012 Mensajes: 316 Ubicación: Nis
|
 Publicado: Mar Mar 18, 2014 10:28 am Asunto: Thats it |
|
 Publicado: Mar Mar 18, 2014 10:28 am Asunto: Thats it |
|
|
Srdjan wrote:
Very interesting, here is just said r
"You can see there is such a turn on after the two screws, the fixed part is connected with the aperture mechanism M / A switch-related, can be removed, the original screw locations to remember. After removing the aperture can be controlled automatically A / M switch ring is removed, when you remove a little slower, attention will locate ball pop up. Fengyun ball as A / M switch rings for positioning. The ball should be removed again following steps."
But there is no way I can do that like is stuck somehow
Thank you I have to look and make some research _________________ Perfection is just another type of anomaly |
|
| Volver arriba |
|
 |
calvin83
 Registrado: 12 Abr 2009 Mensajes: 7740 Ubicación: Hong Kong
|
 Publicado: Mar Mar 18, 2014 10:54 am Asunto: |
|
 Publicado: Mar Mar 18, 2014 10:54 am Asunto: |
|
|
calvin83 wrote:
That can be roughly translate to:
| Cita: |
| You need to unscrew the ring to see the two screws related to the A/M switch. Mark the position of the two screws to ensure you can place them when put them back. You can remove the A/M control ring after removing two screws(watch for the metal ball). Then you can remove the rings in the next photo and access to the three screws holding the rear part. |
_________________ The best lens is the one you have with you.
https://lensfever.com/
https://www.instagram.com/_lens_fever/ |
|
| Volver arriba |
|
 |
Srdjan
 Registrado: 11 Abr 2012 Mensajes: 316 Ubicación: Nis
|
 Publicado: Mar Mar 18, 2014 11:17 am Asunto: |
|
 Publicado: Mar Mar 18, 2014 11:17 am Asunto: |
|
|
Srdjan wrote:
I remove two screws and I can't remove A/M control ring. Like A/M control ring is less wider than helicoid of ring that goes above it (in which direction suppose to go out). It is plastic ring, maybe I have to bent it somehow any clue? It is strange _________________ Perfection is just another type of anomaly |
|
| Volver arriba |
|
 |
Srdjan
 Registrado: 11 Abr 2012 Mensajes: 316 Ubicación: Nis
|
 Publicado: Mar Mar 18, 2014 11:30 am Asunto: |
|
 Publicado: Mar Mar 18, 2014 11:30 am Asunto: |
|
|
Srdjan wrote:
This is how this ring look like. And the part that I paint in red gives me problem to take it out, do I need special tool?
 _________________ Perfection is just another type of anomaly |
|
| Volver arriba |
|
 |
calvin83
 Registrado: 12 Abr 2009 Mensajes: 7740 Ubicación: Hong Kong
|
 Publicado: Mar Mar 18, 2014 11:37 am Asunto: |
|
 Publicado: Mar Mar 18, 2014 11:37 am Asunto: |
|
|
calvin83 wrote:
It looks like you may need to bent it a bit to move it but I am not sure. _________________ The best lens is the one you have with you.
https://lensfever.com/
https://www.instagram.com/_lens_fever/ |
|
| Volver arriba |
|
 |
|
|
|
No puedes publicar temas nuevos en este foro No puedes responder a temas en este foro No puedes editar tus mensajes en este foro No puedes borrar tus mensajes en este foro No puedes votar en las encuestas de este foro
|