MFlenses - Una nueva vida en la era digital
MFLenses 2026

Foro de objetivos de enfoque manual

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.
Destacado

Espacio de socio destacado en la portada del foro.

OM to Nikon adapter DIY style
Ver tema anterior :: Ver tema siguiente  


Reply

stingOM's post inspired me to do this. Knowing that a local junk shop had a Zuiko 35mm f2.8 for a fiver and an OM fitting zoom lens I decided to give it a go. The problem with Leitax, although the adapter looks great, its bloody expensive. But using their instructions I made this little adapter. For the nikon bayonet I used a reversing ring (ebay, china £2)



I checked Leitax's page for my particular lens... http://www.leitax.com/conversion/Olympus-OM/Zuiko-3528/index.html
... and followed the instructions up to the point of attaching their adapter. The spring came from the Olympus mount.

I sawed off the filter mount from the reversing ring. The ring was attached to my camera and the lens sans mount was held against it. There was no infinity focus. So I clamped the ring in a vice and filed about 0.4mm from the thickness of the mount, trying the lens every now and then to check infinity. When I got infinity I put a rear lens cap on the mount and rubbed the back over a sheet of 80 grit sandpaper to even out the thickness. using a finer grit (200) to smooth it off. And painted the 'silver' side black.

Placing the zuiko mount over the nikon ring (lining up the red dots) I marked where the screw holes need to go and drilled them out. I screwed the adapter on the lens and tried it, perfect! of course the screw heads bound with my lens mount so I had to carefully drill counter sinks for the screws.

Finishing off:
The zuiko's have 2 large buttons on the lens barrel, one for stopdown and the other is the lens lock. I removed these from the Olympus mount and glued them into the gaps on the lens barrel. I also used epoxy putty to fill in the gaps normally hidden under the Zuiko's silver mount. I used metal adhesive tape to cover the filler and make it look nicer. Copper tape was used initially but that has been replaced with aluminium tape. Mimicking the Zuiko's mount nicely.

Of course this is a one-way conversion. The 28mm f3.5 was better in that I could put the original mount back on. The lens barrel buttons were left in the mount and the gaps just filled with epoxy resin. How did I stop it sticking to the Zuiko? Easy, I painted a little oil in the gaps where the filler went. The putty stayed in nicely and when hard pulled out cleanly. I removed any oil residue and put the plugs back in. I then put a little drop of epoxy on each of the plugs before screwing the adapter back on. The filler then stuck to the adapter, not the lens. A piece of rubber focus grip over the filler finished it off nicely.

I did this conversion to a Tokina 70-210. The aperture ring was next to the lens mount and would easily drop off. The great thing with this conversion was that the filter thread from the reversing ring didn't have to come off and held the aperture ring in its place. I lubricated the filter ring with a little candle wax and the aperture ring runs smoothly. Again I used the spring from the mount to hold the aperture open.


Reply

Excellent work Phil!

I might have to try this as OM lenses are cheaper and easier to find than Nikkors.


Reply

Go to Leitax as their site shows how to dismantle the lens (each is different) and hold the aperture open. Expect a lot of filing of the reversing ring. A body cap is far too thick.

My 28mm has a Dandelion attached so I can use it and meter. The EXIF data tells you its a 28mm f3.5 at F3.5 aperture.


Reply

Cheers Phil. I've been looking at the info. Today I hacked a Pentacon 2.8/28 to Nikon using a M42-Nikon adapter that cost the whopping total of 1.08ukp. Tomorrow I;m going to do the same with a Pentacon 1.8/50, then I might have a go at a Pentacon 2.8/135 too, nice lenses that I never use and can turn intos omething much more useful for me.


Reply

Well I thought great! until you mentioned it's a one way conversion Sad cos I have a VIV 24mm f2 OM mount and only have a crappy OM20 and it would have been nice for my Nikon camera.


Reply

Excalibur escribió:
Well I thought great! until you mentioned it's a one way conversion Sad cos I have a VIV 24mm f2 OM mount and only have a crappy OM20 and it would have been nice for my Nikon camera.


It may not be a one way conversion. Third party OM lenses can be easier to adapt because the aperture ring is in the 'normal' place - not the front.

Take off the mount and have a look, there may be room to work. If the aperture ring butts up to the lens mount be very careful.

I converted a Tokina 70-210 OM zoom. The filter thread on the reversing ring actually held everything in place and I screwed it on with long screws. Took 10 minutes (plus half an hour getting the screw holes lined up!)


Reply

Phil, I'd love to hear what lenses you have successfully converted to Nikon. I'm hoping to convert my Icarex bayonet mount Skoparex 3.4/35. 35mm is my favourite focal length on APS-C so I need a Nikon fit 35.


Reply

philslizzy escribió:
Excalibur escribió:
Well I thought great! until you mentioned it's a one way conversion Sad cos I have a VIV 24mm f2 OM mount and only have a crappy OM20 and it would have been nice for my Nikon camera.


It may not be a one way conversion. Third party OM lenses can be easier to adapt because the aperture ring is in the 'normal' place - not the front.

Take off the mount and have a look, there may be room to work. If the aperture ring butts up to the lens mount be very careful.

I converted a Tokina 70-210 OM zoom. The filter thread on the reversing ring actually held everything in place and I screwed it on with long screws. Took 10 minutes (plus half an hour getting the screw holes lined up!)


Thanks that's an idea as I too have a Tokina zoom OM mount that I don't use and can try.


Reply

iangreenhalgh1 escribió:
Phil, I'd love to hear what lenses you have successfully converted to Nikon. I'm hoping to convert my Icarex bayonet mount Skoparex 3.4/35. 35mm is my favourite focal length on APS-C so I need a Nikon fit 35.


The Icarex is 48mm (I think). so its longer than Nikon. It all depends on whether you want to go reversal or not. My 35mm is non reversible but my 28mm is.

You really dont want to 'ruin' a rareish lens for this purpose but you could probably adapt it easily with a file, reversing ring and some epoxy putty.

I have successfully converted:

Zuiko 35mm f2.8
Zuiko 28mm f3.5
Pentacon MC Electric 135 f3.5
Tokina 70-210

The Tokina came with a bunch of Oly stuff, I liked it because its so small when collapsed.

pics of the Tokina:







The hard part when converting lenses using a reversing ring is getting the lens mount holes lined up. As you can see from the photos above I had at least 2 attempts before getting it.

Now, I use a ring of clear plastic - a fruit punnet lid is good. Put the original adapter over it and mark off where the holes need to be. And mark where the aperture & focus index is too. Cut it out, and make holes where the marks are. I reverse it and put it against the reversing ring and scratch crosses where the holes need to be. You usually get 2 out of 4 right first time.

The Pentacon would not convert using this method, so I sawed off the bayonet part of a ruined reversing ring and it slipped right over the M42 screw. It needed filing down inside a bit but it slipped on. A better fit than using an adapter because of no thickness. OK not quite infinity (15 to 20metres) but good enough for my portraits. I glued the mount on it and ground a small depression where the Nikon locking pin went. I had played with the infinity stop but couldnt get it to go back quite enough but I did move it.

I did think of filing it just to get that extra half a mil but it was good enough for me.

Then I sold it.