MFlenses - Una nueva vida en la era digital
MFLenses 2026

Foro de objetivos de enfoque manual

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.
Destacado

Espacio de socio destacado en la portada del foro.

Ni-MH batteries and flash
Ver tema anterior :: Ver tema siguiente  


Reply

Mecablitz 45 user guide escribió:
The battery housing must not be fitted with NiCad batteries! The contacts of the battery housing are only intended for alkaline manganese batteries.
The lower resistance of NiCad Batteries means that more current can flow, and this can damage the flashgun. (..)


Any idea if Ni-Mh could be used?
I've been using them with modern flashes.


Reply

All are used batteries.

Duracell Aerocell Super-Alkaline 0.28 ohms.
Duracell ProCell 0.26 ohms.
Varta Alkaline 0.30 ohms.

Panasonic Ni-MH 0.25 ohms.
Tecxus Ni-MH 0.24 ohms.

Does this make a difference?

edit: corrected the ohms, damn USSR meter. Embarassed


Editado por última vez por kansalliskala el Mar Mayo 08, 2012 8:42 am; editado 2 veces en total


Reply

I have used both NiCa and NiMe on older flashes.

What to be concern is the high ampere rate of these batteries. Full power continously after 30-40 shots will melt down the battery compartment and deformed metal springs. These parts need to be replaced. I also had modified several of mine with thicker internal electrical cable or, if place is problem internally, added few more thin cables.

I have been used these batteries with maximum 1/4 power. No problem so far, as long as you aware of heat problem.

Now, if i need power, I use many flashes, bundled with cheap eby radio receivers, but still at 1/4 power. Old manual flashes cost me approx 10euro a piece.

edit: high Ohm low ampere rate


Reply

hoanpham escribió:
Full power continously after 30-40 shots will melt down the battery compartment and deformed metal springs.


Ok, thank you. The basic problem is this, I can deal with that, just turn it off when the handle starts to feel too warm.

I was afraid it would disturb the electronics or explode the capacitors which is not nice when they are just about where my left eye is. Shocked


Reply

http://www.ka7oei.com/nicds.html

Here is something but I don't understand the ohms and amperes, I studied to be a mechanical engineer. Confused


Reply

The site has some good hints on rechargable cells.

I have 50+ AA NiMh 2300 mAh and use them with flashes.
My charger is per cell, designed for NiMh.
I also nummerize 4/6 batteries as a set (a1, a2, a3, a4, b1, b2...) and always keep them as a set for ease maintenance/charge/discharge. I may depend on these cells one day.


Reply

Recommend a good charger with NiMH's, this is the one I use:

http://www.mahaenergy.com/store/viewitem.asp?idproduct=407


Reply

Katastrofo escribió:
Recommend a good charger with NiMH's, this is the one I use:

http://www.mahaenergy.com/store/viewitem.asp?idproduct=407


Shocked $89.85

I got most of my Ni-MH:s from a local store for a give-away price. Something like 1,50 € for a charger and 4 AA-s. But they are probably not the best quality. I've usually tossed the chargers away and kept just the batteries.


Reply

The MAHA does both AAA and AA batts, if that lessens the sting. Having a smart charger that will drain out
whatever residual power is left before recharging is a definite plus. Using a cheap charger, my batteries were
crapping out in half the time as they do now.