| Ver tema anterior :: Ver tema siguiente |
| Autor |
Mensaje |
Jay Ace
Registrado: 03 Jul 2010 Mensajes: 17 Ubicación: Lexington, KY
|
 Publicado: Dom Jul 04, 2010 3:11 am Asunto: CZ Jena Pancolar f/1.8 50mm Re-Assembly |
|
 Publicado: Dom Jul 04, 2010 3:11 am Asunto: CZ Jena Pancolar f/1.8 50mm Re-Assembly |
|
|
Jay Ace wrote:
I wish my first post was not about asking for help but it is what it is.
Got this lens from overseas and when it got here it seemed it was very dirty on the inside as focus was very rough and it had some flat spots and aperture ring was very loose. Seller offered to replace it but I didn't want to spend more money on shipping so decided to clean it myself as I'm big on DIY but I have never tackled such a task before.
It was easy to take apart and lubricate properly so the focus is now super smooth and has good resistance. Problem I encountered was with aperture ring mostly. It used to be super loose but now it's extremely tight. When I took the aperture ring off there were couple of ball bearings just floating around in there which I believe caused the looseness as they have fallen out of their proper spot and I have no clue where they belong.
Anyway, I have several question and I will post some photographs of specific areas I have questions about but for now I wanted to see if anyone has taken this lens apart and can provide some guidance or anyone knows of a DIY online.
Any help is much appreciated  |
|
| Volver arriba |
|
 |
Attila
 Registrado: 24 Feb 2007 Mensajes: 58002
Expire: 2025-11-18
|
 Publicado: Dom Jul 04, 2010 4:14 pm Asunto: |
|
 Publicado: Dom Jul 04, 2010 4:14 pm Asunto: |
|
|
Attila wrote:
Welcome Jay!
Only one small ball have place under aperture ring and provide stops at every aperture. Easy to find their place , sorry I don't have any description how to do it , but you will find it I am sure. |
|
| Volver arriba |
|
 |
Jay Ace
Registrado: 03 Jul 2010 Mensajes: 17 Ubicación: Lexington, KY
|
|
| Volver arriba |
|
 |
sichko
 Registrado: 20 Jun 2008 Mensajes: 2475 Ubicación: South West UK
|
 Publicado: Dom Jul 04, 2010 6:24 pm Asunto: |
|
 Publicado: Dom Jul 04, 2010 6:24 pm Asunto: |
|
|
sichko wrote:
Hi. I'm not familiar with this lens but I am guessing that it has been (re)assembled incorrectly. I do not believe that the two parts (the "slot" and the "prong") which the arrow points to in the first picture should disengage when you focus. Has the part with the the "prong" been fitted upside down ? _________________ John |
|
| Volver arriba |
|
 |
Jay Ace
Registrado: 03 Jul 2010 Mensajes: 17 Ubicación: Lexington, KY
|
 Publicado: Dom Jul 04, 2010 7:53 pm Asunto: |
|
 Publicado: Dom Jul 04, 2010 7:53 pm Asunto: |
|
|
Jay Ace wrote:
I know what you mean and I have checked it but simply there is no way to put the aperture ring on upside-down. Prong and slot parts I did not take off so as far as I know that's how they are supposed to be mounted. |
|
| Volver arriba |
|
 |
sichko
 Registrado: 20 Jun 2008 Mensajes: 2475 Ubicación: South West UK
|
 Publicado: Dom Jul 04, 2010 10:01 pm Asunto: |
|
 Publicado: Dom Jul 04, 2010 10:01 pm Asunto: |
|
|
sichko wrote:
It's often worth searching the forum, either directly or via Google. So...
http://forum.mflenses.com/pancolar-50-18---disassemble-amp-clean-t16511.html
gives a link which apparently describes the disassembly of the Pancolar. Access requires you to join a Yahoo group so I don't know if it's useful. But it might be worth a look. _________________ John |
|
| Volver arriba |
|
 |
Gonzoo
 Registrado: 29 Mar 2010 Mensajes: 231
|
 Publicado: Dom Jul 04, 2010 10:07 pm Asunto: |
|
 Publicado: Dom Jul 04, 2010 10:07 pm Asunto: |
|
|
Gonzoo wrote:
If the prong disengages the slot, my guess is, that the helicoid was screwed in incorrectly. You have to trial and error until you get the right helicoid position. The prong shouldn't disengage the slot then.
Good luck! _________________ Canon 5d | Exa 500 | Pentacon Six + too much lenses  |
|
| Volver arriba |
|
 |
Jay Ace
Registrado: 03 Jul 2010 Mensajes: 17 Ubicación: Lexington, KY
|
 Publicado: Dom Jul 04, 2010 10:16 pm Asunto: |
|
 Publicado: Dom Jul 04, 2010 10:16 pm Asunto: |
|
|
Jay Ace wrote:
Thanks for the link! I'm trying to join the group ...
Believe me I have been searching quite a bit but did not find anything that was of any help, unfortunately. |
|
| Volver arriba |
|
 |
martyn_bannister
 Registrado: 23 Mayo 2010 Mensajes: 1151
|
 Publicado: Mar Ago 10, 2010 5:32 pm Asunto: |
|
 Publicado: Mar Ago 10, 2010 5:32 pm Asunto: |
|
|
martyn_bannister wrote:
Hi Jay,
Don't know whether you solved this, but has the prong that engages the slot been put on upside down? i.e. should it project into the body, rather than out?
I have a very similar lens, so maybe I can take pictures if you are still in difficulty? |
|
| Volver arriba |
|
 |
Jay Ace
Registrado: 03 Jul 2010 Mensajes: 17 Ubicación: Lexington, KY
|
 Publicado: Mar Ago 10, 2010 9:44 pm Asunto: |
|
 Publicado: Mar Ago 10, 2010 9:44 pm Asunto: |
|
|
Jay Ace wrote:
No, never did figure it out. The thing about the prong is that I've never removed from the ring in the first place but I think someone else suggested that same thing and I have tried mounting it pointing down but it just doesn't fit that way.
I love to DIY but at this point I'm looking for someone to do it for me as I just can't figure it out  |
|
| Volver arriba |
|
 |
martyn_bannister
 Registrado: 23 Mayo 2010 Mensajes: 1151
|
 Publicado: Mié Ago 11, 2010 5:07 pm Asunto: |
|
 Publicado: Mié Ago 11, 2010 5:07 pm Asunto: |
|
|
martyn_bannister wrote:
| Jay Ace escribió: |
No, never did figure it out. The thing about the prong is that I've never removed from the ring in the first place but I think someone else suggested that same thing and I have tried mounting it pointing down but it just doesn't fit that way.
I love to DIY but at this point I'm looking for someone to do it for me as I just can't figure it out  |
I'll open my lens tomorrow and have a look...... |
|
| Volver arriba |
|
 |
martyn_bannister
 Registrado: 23 Mayo 2010 Mensajes: 1151
|
|
| Volver arriba |
|
 |
Jay Ace
Registrado: 03 Jul 2010 Mensajes: 17 Ubicación: Lexington, KY
|
 Publicado: Vie Ago 13, 2010 1:14 am Asunto: |
|
 Publicado: Vie Ago 13, 2010 1:14 am Asunto: |
|
|
Jay Ace wrote:
That a lot for doing that. I really appreciate it!
Unfortunately your lens is very similar but on the inside they are different and the prong on mine just can not be mounted the other way. It's shaped differently than yours and there is just no room for it if it was mounted upside down.
Thanks again  |
|
| Volver arriba |
|
 |
martyn_bannister
 Registrado: 23 Mayo 2010 Mensajes: 1151
|
 Publicado: Vie Ago 13, 2010 7:42 am Asunto: |
|
 Publicado: Vie Ago 13, 2010 7:42 am Asunto: |
|
|
martyn_bannister wrote:
| Jay Ace escribió: |
That a lot for doing that. I really appreciate it!
Unfortunately your lens is very similar but on the inside they are different and the prong on mine just can not be mounted the other way. It's shaped differently than yours and there is just no room for it if it was mounted upside down.
Thanks again  |
I noticed that your prong was a different shape, but it looked like it could be inverted. I think the differences might be because mine is the electric version. Oh well, at least you know where the two balls go now. Maybe someone else has the exact same lens as yours and can help? Best of luck. |
|
| Volver arriba |
|
 |
|
|
|
No puedes publicar temas nuevos en este foro No puedes responder a temas en este foro No puedes editar tus mensajes en este foro No puedes borrar tus mensajes en este foro No puedes votar en las encuestas de este foro
|