MFlenses - Una nueva vida en la era digital
MFLenses 2026

Foro de objetivos de enfoque manual

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.

Explora el mundo de los objetivos antiguos mediante notas de reparación, pruebas reales e hilos de archivo llenos de imágenes.
Destacado

Espacio de socio destacado en la portada del foro.

how to remove stripped screw off lens mount
Ver tema anterior :: Ver tema siguiente  


Reply

All,

as the title suggests, I was trying to open one of my lens which has a stuck focus barrel. The screws holding the lens mount, as it turns out, are made of very soft material and now the slot in the screw heads were stripped.

I did some web search and found a few approaches(eg http://www.wikihow.com/Remove-a-Stripped-Screw); but I do not know whether I can try them since the screws on the lens are very small(2mm slot type screw). I would appreciate your help and suggestions.

thanks for your time,
Cheers,


Reply

I am in danger of having the same problem

patrickh


Reply

Something similar a screw tip of cheap screwdriver stuck in the screw Shocked


Reply

Hello there,
Assuming that the screw is still firmly stuck in the lens (i.e. is not loose), then try something pointed and hard (like an engineer's scriber - it's big enough to hold properly) and by repeatedly scratching across the head of the screw create a new groove.
Then, before you try to remove the screw, use solvent to loosen any locking compound on the thread. I would use at least de-natured alcohol and acetone, since I have found screws locked with compounds that do not loosen in alcohol or do not loosen in acetone. (As far as I can tell the early Vivitars need acetone, most others have responded to alcohol.)

regards

Angus


Reply

a risky last-ditch solution is to clean the head with solvent and use a tiny droplet of epoxy to bond an old throw-away slightly smaller screwdriver to it, being ultra-careful not to let epoxy reach hole threads. after the epoxy sets unscrew. note some epoxies get thin and runny when curing; definitely not recommended.


Reply

@siriusdogstar: thanks for the suggestions. I will try photomac's solution first(ie. make a bigger slot); if that fails, then I will fill the slot and glue some old nail/screw to provide a better grip

@Photomac: I have tried something called "liquid wrench" and it did not help. I will get some iso-alcohol to give it a try.

Cheers


Reply

Hi Cheve,

For next time the main thing is to use a perfectly-fitting screwdriver with a good grip. All mine have short lengths of thick hose on the shafts - you need to be able to exert force with control and you can't do that with normal jeweller's drivers. And cheap screwdrivers are worse than useless.

Screws are often jammed in older lenses. Heating the head of the screw with a soldering iron before you try to remove it helps a lot. Then plenty of downward pressure on the driver and a quick but controlled leftward twist usually does the trick. It takes practice though, no guarantees given!

Once a screw head is damaged things are much harder - you may have to use a small burr on a Dremel-type tool to remove the head, then once the mount is off you can undo the remains of the screw with pliers. A burr is much easier to keep centred in the screw head than a drill. Of course this assumes you have a replacement screw. I like diamond burrs by the way, very cheap nowadays.

No such thing as a screw extractor in a small enough size to be any help with cameras or lenses I'm afraid - the rest of the advice on the Wiki site is OK but if you're going to try to strike the head of a screw on a lens do it gently & carefully and bear in mind that cast alloys crack easily.

You may want to see whether the focus threads can be accessed from the front. A little tip for removing the front bezel - usually the first step - is to use double-sided sticky tape. A small piece either side, then your thumbs can get enough grip to unscrew it.

I doubt anyone reading this needs to be told but... don't use the soldering iron trick on a plastic lens...

Happy holidays!