| Ver tema anterior :: Ver tema siguiente |
| Autor |
Mensaje |
Katastrofo
 Registrado: 26 Feb 2007 Mensajes: 10405 Ubicación: USA
Expire: 2013-11-19
|
 Publicado: Vie Nov 13, 2009 1:35 pm Asunto: Agfa Neutol? |
|
 Publicado: Vie Nov 13, 2009 1:35 pm Asunto: Agfa Neutol? |
|
|
Katastrofo wrote:
Has anyone used the above and do you have samples? Found an
example off of flickr:
http://farm3.static.flickr.com/2114/2358543794_21edf9d06f_o.jpg
Hummm. |
|
| Volver arriba |
|
 |
Sevo
 Registrado: 22 Ago 2008 Mensajes: 1189 Ubicación: Frankfurt, Germany
Expire: 2012-12-03
|
 Publicado: Vie Nov 13, 2009 2:56 pm Asunto: |
|
 Publicado: Vie Nov 13, 2009 2:56 pm Asunto: |
|
|
Sevo wrote:
That is (or was) the standard Agfa paper developer, and does not differ much from those from Ilford or Kodak. I suppose the print was developed in it rather than the film. _________________ Sevo |
|
| Volver arriba |
|
 |
Katastrofo
 Registrado: 26 Feb 2007 Mensajes: 10405 Ubicación: USA
Expire: 2013-11-19
|
 Publicado: Vie Nov 13, 2009 3:02 pm Asunto: |
|
 Publicado: Vie Nov 13, 2009 3:02 pm Asunto: |
|
|
Katastrofo wrote:
Sevo, thanks. It looks good if I ever start printing. |
|
| Volver arriba |
|
 |
Seele
 Registrado: 17 Abr 2009 Mensajes: 746 Ubicación: Sydney Australia
|
 Publicado: Vie Nov 13, 2009 4:08 pm Asunto: |
|
 Publicado: Vie Nov 13, 2009 4:08 pm Asunto: |
|
|
Seele wrote:
I used Neutal NE quite a lot and it's a standard print developer, Neutal WA gave warm tones when matched with suitable papers; I certainly miss Portriga!
Since you compound your solutions from raw chemicals, when you are to do printing, there would be no shortage of formulae for paper developers to try out. From a comparative test I conducted a few years ago, I found that Focal Universal is a good one for allround work at low cost, but MCM Winchester (original formula) gives outstanding results, perhaps even slightly better than Neutol. |
|
| Volver arriba |
|
 |
Katastrofo
 Registrado: 26 Feb 2007 Mensajes: 10405 Ubicación: USA
Expire: 2013-11-19
|
 Publicado: Sáb Nov 14, 2009 1:48 am Asunto: |
|
 Publicado: Sáb Nov 14, 2009 1:48 am Asunto: |
|
|
Katastrofo wrote:
Seele, thanks for the heads-up on the formulas. I'm a ways from doing
printing, but mixing raw chems is almost 2nd nature after my navy
experience. |
|
| Volver arriba |
|
 |
Seele
 Registrado: 17 Abr 2009 Mensajes: 746 Ubicación: Sydney Australia
|
 Publicado: Sáb Nov 14, 2009 5:38 am Asunto: |
|
 Publicado: Sáb Nov 14, 2009 5:38 am Asunto: |
|
|
Seele wrote:
In case you cannot find the recipes for the two paper developers I mentioned, here they are:
MCM Winchester
Metol 4.25g
Sodium sulphite (anhydrous) 50g
Hydroquinone 12.5g
Sodium carbonate (anhydrous) 100g
Potassium bromide 6.25g
Water to 1 litre
To use, dilute 1:3.
If you use sodium carbonate in monohydrate form, use 118.5g instead.
Personal notes taken after comparison test:
"This gives very brilliant, clean-looking prints on baryta papers. Light to mid greys appear to have extra separation, whites stay very bright, but highlight details, if too weak, can be brought out by methods like prior treatment in Ansco 120. Compared to standard developers such as Ilford MG, the blacks seem to have an extra depth which goes right into the paper."
____
Focal Universal
Metol 1g
Sodium sulphite (anhydrous) 25g
Hydroquinone 3.7g
Sodium carbonate (anhydrous) 25g
Potassium bromide 0.3g
Water to 1 litre
To use, dilute 1:1
If you use sodium carbonate in monohydrate form, use 30g instead.
Personal notes taken after comparison test:
"This behaves in a similar way as Ilford MG, but without the slight compression of mid greys. Development times should be a little longer, say an extra 50%."
Hope this is of interest. |
|
| Volver arriba |
|
 |
Katastrofo
 Registrado: 26 Feb 2007 Mensajes: 10405 Ubicación: USA
Expire: 2013-11-19
|
 Publicado: Sáb Nov 14, 2009 2:46 pm Asunto: |
|
 Publicado: Sáb Nov 14, 2009 2:46 pm Asunto: |
|
|
Katastrofo wrote:
Seele, thanks much for this! I'm going to bookmark this thread.
Actually, will see about printing this out, too. |
|
| Volver arriba |
|
 |
|
|
|
No puedes publicar temas nuevos en este foro No puedes responder a temas en este foro No puedes editar tus mensajes en este foro No puedes borrar tus mensajes en este foro No puedes votar en las encuestas de este foro
|