| Ver tema anterior :: Ver tema siguiente |
| Autor |
Mensaje |
eddie3dfx
Registrado: 12 Sep 2013 Mensajes: 9
|
 Publicado: Jue Sep 12, 2013 6:21 pm Asunto: Need help repairing a planar 50mm 1.4 |
|
 Publicado: Jue Sep 12, 2013 6:21 pm Asunto: Need help repairing a planar 50mm 1.4 |
|
|
eddie3dfx wrote:
I picked up a planar 50mm 1.4 from someone with the sale based on the sale that the aperture was stuck wide open.
I took the back apart to take a look at the aperture blades.
In the picture that I shown, I wanted to confirm that 1 goes to 1 and 2 goes to 2.
How and where does level 2 on the top with shim connect into the assembly. (to left of assembly 2, to the right of it, or clicked into it somehow.. is there a spring that's missing?)
The reason why I ask this is because level one opens and closes the aperture with little effort. I'm assuming this means it's not stuck from grim/grease but something else that is wrong.
I put a question mark in where lever 1 moves the aperture but seemingly goes to far leaving it wide open (which I believe is what's happening.
Any ideas? I am at a loss
I looked at pictures of other peoples repairs but it was hard to see the inner workings of where these levers were and what moved what.
I also attached 2 videos (vimeo takes 20 mins to upload, so if it doesn't work, it will shortly)
http://postimg.org/image/xil8oyyjp/
http://postimg.org/image/df1mcx6jp/
https://vimeo.com/74398712
https://vimeo.com/74398711
[/img]
Editado por última vez por eddie3dfx el Jue Sep 12, 2013 6:31 pm; editado 1 vez en total |
|
| Volver arriba |
|
 |
Nordentro
 Registrado: 24 Jun 2010 Mensajes: 4738 Ubicación: Lillehammer, Norway
Expire: 2015-01-29
|
 Publicado: Jue Sep 12, 2013 6:29 pm Asunto: Re: Need help repairing a planar 50mm 1.4 |
|
 Publicado: Jue Sep 12, 2013 6:29 pm Asunto: Re: Need help repairing a planar 50mm 1.4 |
|
|
Nordentro wrote:
| eddie3dfx escribió: |
I picked up a planar 50mm 1.4 from someone with the sale based on the sale that the aperture was stuck wide open.
I took the back apart to take a look at the aperture blades.
In the picture that I shown, I wanted to confirm that 1 goes to 1 and 2 goes to 2.
How and where does level 2 on the top with shim connect into the assembly. (to left of assembly 2, to the right of it, or clicked into it somehow.. is there a spring that's missing?)
The reason why I ask this is because level one opens and closes the aperture with little effort. I'm assuming this means it's not stuck from grim/grease but something else that is wrong.
I put a question mark in where lever 1 moves the aperture but seemingly goes to far leaving it wide open (which I believe is what's happening.
Any ideas? I am at a loss
I looked at pictures of other peoples repairs but it was hard to see the inner workings of where these levers were and what moved what.
I also attached 2 videos (vimeo takes 20 mins to upload, so if it doesn't work, it will shortly)
https://vimeo.com/74398712
https://vimeo.com/74398711
|
Welcome to the forum, the forum has a antispam thingy at the first post, you are good from now on  _________________ Lars | Manuellfokus.no
Editado por última vez por Nordentro el Jue Sep 12, 2013 6:32 pm; editado 1 vez en total |
|
| Volver arriba |
|
 |
eddie3dfx
Registrado: 12 Sep 2013 Mensajes: 9
|
 Publicado: Jue Sep 12, 2013 6:31 pm Asunto: |
|
 Publicado: Jue Sep 12, 2013 6:31 pm Asunto: |
|
|
eddie3dfx wrote:
Thank you, not sure why I have such a hard time uploading pics  |
|
| Volver arriba |
|
 |
Nordentro
 Registrado: 24 Jun 2010 Mensajes: 4738 Ubicación: Lillehammer, Norway
Expire: 2015-01-29
|
 Publicado: Jue Sep 12, 2013 6:33 pm Asunto: |
|
 Publicado: Jue Sep 12, 2013 6:33 pm Asunto: |
|
|
Nordentro wrote:
| eddie3dfx escribió: |
Thank you, not sure why I have such a hard time uploading pics  |
Antispam, you can post pictures as normal from now on
I can´t help you with this lens, but I am sure others can as this is a pretty common "keeper"  _________________ Lars | Manuellfokus.no |
|
| Volver arriba |
|
 |
eddie3dfx
Registrado: 12 Sep 2013 Mensajes: 9
|
 Publicado: Jue Sep 12, 2013 10:05 pm Asunto: |
|
 Publicado: Jue Sep 12, 2013 10:05 pm Asunto: |
|
|
eddie3dfx wrote:
I have come to the conclusion it's one of two things.
I kind of ghetto wedged a tighter spring in between the hole and the plastic piece. It now snaps back to f4 through F1.4.
So either the original spring has lost tension or .. the aperture blades are dirty causing the loss of spap back... It's hard to tell because I thought I could solve this with just pulling the back apart.. No, i'll have to do a full clean.
I misunderstood the mechanics of the lens... I must be cleaned..
Besides lighter fluid, what can I use to clean the barrel, components? What kind of grease do you use on the threads? |
|
| Volver arriba |
|
 |
Clarkee
Registrado: 25 Sep 2013 Mensajes: 2 Ubicación: United Kingdom
|
 Publicado: Mié Sep 25, 2013 12:45 pm Asunto: |
|
 Publicado: Mié Sep 25, 2013 12:45 pm Asunto: |
|
|
Clarkee wrote:
It only takes a tiny bit of oil to stop an aperture working.
Just think how much tension is on that tiny spring?
And how much tension your fat fingers can exert? (No offence meant).
Take all the glass out & flood clean it. With lighter fluid.
Unsure if this can be done without taking the helicoids apart.
(Make a note of exactly where they come apart on dissassembly!)
I use Silicon grease for O rings etc.
but some people say it is unsuitable. Different lenses do require difference grease Viscositys.
Molybdenum Disulfite is also popular.
Depending on tolerances, I assume the grease you would need for a Zeiss is quite thin.
Is it Contax/Yashica mount?
I have one but never stripped it down. |
|
| Volver arriba |
|
 |
Lloydy
 Registrado: 02 Sep 2009 Mensajes: 7880 Ubicación: Ironbridge. UK.
Expire: 2022-01-01
|
 Publicado: Mié Sep 25, 2013 1:15 pm Asunto: |
|
 Publicado: Mié Sep 25, 2013 1:15 pm Asunto: |
|
|
Lloydy wrote:
| Cita: |
| Molybdenum Disulfite is also popular. |
I'm not a fan of moly' grease for lenses, for the reason that when I was an engineering maintainence guy we used moly' in a lot of industrial equipment so we had big drums of the stuff in various grades in our workshop store, and every drum would have a small pool of oil on the top that had seperated out. And the longer it was left without moving the bigger the pool. The other multi purpose and high pressure greases didn't seem to have this problem with seperation. In my experience all the metal based lubricants seem to seperate from the oil in certain circumstances, you see it happen in Copperslip and the aluminium based anti-seize lubricants
So I use a light grade multi purpose grease for lenses, the sort of stuff you would use for bicycle bearings. But I have used silicone oil on helicoids as well, and that seems fine in very small quantities, just a smear with a tiny paint brush.
Moly' is popular I know, so I guess the seperation thing might not be the problem in lenses I think it might be? I just work on my instinct and use a grease that seems more stable. _________________ LENSES & CAMERAS FOR SALE.....
I have loads of stuff that I have to get rid of, if you see me commenting about something I have got and you want one, ask me.
My Flickr https://www.flickr.com/photos/mudplugga/
My ipernity -
http://www.ipernity.com/home/294337 |
|
| Volver arriba |
|
 |
eddie3dfx
Registrado: 12 Sep 2013 Mensajes: 9
|
 Publicado: Sáb Sep 28, 2013 6:51 pm Asunto: |
|
 Publicado: Sáb Sep 28, 2013 6:51 pm Asunto: |
|
|
eddie3dfx wrote:
Had to send it in to get the aperture cleaned. I couldn't get the front unscrewed (zeiss puts a tab of glue to hold it in)
Didn't want to break it and I felt the price was reasonable enough to get it cleaned.
Yeah, the aperture blades were dirty and he said the top piece holding it in was also screwed on too tight, which caused it to be too tight as well. |
|
| Volver arriba |
|
 |
|
|
|
No puedes publicar temas nuevos en este foro No puedes responder a temas en este foro No puedes editar tus mensajes en este foro No puedes borrar tus mensajes en este foro No puedes votar en las encuestas de este foro
|